aluminum electrolytic capacitors voltage mark for 6.3v is 6v. 105?c marking voltage capacitance lot no. a2p 10 16v plastic platform 0.3 max. 5.4 +0.1 -0.2 d 0.5 b 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e 0.5 to 0.8 positive negative 105?c marking voltage capacitance plastic platform 0.3 max. 6.2 0.3 d 0.5 b + 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e 0.5 to 0.8 positive negative d 4 a b c e 5 6.3 8 1.8 2.1 2.4 3.3 4.3 5.3 6.6 8.3 4.3 5.3 6.6 8.3 1.0 1.3 2.2 2.3 (mm) trade mark lot no. a2p 100 16v u 1 w 2 f 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code capacitance tolerance ( 20%) rated capacitance (10 f) rated voltage (16v) series name ty p e d 4 to 6.3 8 code gb gs wf series chip type, low impedance chip type, low impedance temperature range up to +105 c . designed for surface mounting on high density pc board. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2011/65/eu). chip type ( 4 to 6.3) ( 8) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item 55 to +105 c 6.3 to 35v 1 to 220f 20% at 120hz, 20 c after 2 minutes' application of rated voltage, leakage current is not more than 0.01cv or 3 (a) , whichever is greater. black print on the case top. measurement frequency : 120hz at 20 c measurement frequency : 120hz the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 105 c. after storing the capacitors under no load at 105 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. rated voltage (v) tan ( max. ) 6.3 0.22 10 0.19 16 0.16 25 0.14 35 0.12 z 25 c / z+20 c z 55 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 6.3 2 4 10 2 4 16 2 3 25 2 3 35 2 3 dimensions max. impedance (?) at 20 c 100khz rated ripple current (marms) at 105 c 100khz wf type numbering system (example : 16v 10 f) the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. wt 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 010 1r5 2r2 3r3 4r7 6r8 100 150 220 330 470 680 101 151 221 4 5 5 6.3 6.3 8 8 0j 6.3 1a 10 1c 16 1e 25 1v 35 5.0 2.6 2.6 1.3 1.3 0.8 0.8 50 80 80 115 115 150 150 5 5 6.3 6.3 8 8 2.6 2.6 1.3 1.3 0.8 0.8 80 80 115 115 150 150 4 5 5 6.3 6.3 8 8 5.0 2.6 2.6 1.3 1.3 0.8 0.8 50 80 80 115 115 150 150 4 4 5 6.3 6.3 6.3 8 8 5.0 5.0 2.6 1.3 1.3 1.3 0.8 0.8 50 50 80 115 115 115 150 150 4 4 4 4 4 5 5 6.3 6.3 8 8 5.0 5.0 5.0 5.0 5.0 2.6 2.6 1.3 1.3 0.8 0.8 50 50 50 50 50 80 80 115 115 150 150 v code cap. (f) impedance rated ripple low impedance capacitance change leakage current tan within 20% of the initial capacitance value less than or equal to the initial specified value 200% or less than the initial specified value capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value wg low impedance case size d (mm) taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please select uj(p.164) series if high c/v products are reqired. please refer to page 3 for the minimum order quantity. frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.35 0.50 0.64 0.83 1.00 cat.8100c
|
